HomeMy WebLinkAboutOPI 2021 REPAIRAppendix IX
Underground Storage Tank
Overfill Prevention Equipment Inspection Report Form
CERS = California Environmental Reporting System, ID = Identification, ICC = International Code
Council, OPE = Overfill Prevention Equipment
Page 1 of 2
TYPE OF ACTION ܆܆ Installation ܆ Repair ܆ 36 Month
1. FACILITY INFORMATION
CERS ID Inspection Date
Facility Name
Facility Address City ZIP Code
2. SERVICE TECHNICIAN INFORMATION
Company Performing the Inspection Phone
Mailing Address
Service Technician Performing Inspection
Contractor/Tank Tester License Number
ICC Number Expiration Date
3. TRAINING AND CERTIFICATIONS
Manufacturer and Test Equipment Training Certifications Expiration Date
4. INSPECTION PROCEDURES INFORMATION
Inspection Procedures Used Components Inspected
5. CERTIFICATION BY SERVICE TECHNICIAN CONDUCTING INSPECTION
I hereby certify that the OPE was inspected in accordance with California Code of
Regulations, title 23, division 3, chapter 16, section 2637.2; that required supporting
documentation is attached; and all information contained herein is accurate. I understand
that test procedures shall be made available upon request by the governing authority.
Service Technician Signature Date
10484656 10/4/2021
ARCO AM PM
4203 Ming Avenue Bakersfield 93309
Confidence UST Services, Inc.(800) 339-9930
2209 Zeus Court, Bakersfield, CA 93308
Aaron Perrigo
804904
8485827 8/17/2022
OPW 0148613 8/1/2022
Appendix B Overfill Valves
10/4/2021
Total # of Pages
8
Underground Storage Tank
Overfill Prevention Equipment Inspection Report
Additional copies of this page may be attached.
Attach tank chart(s), measurements, calculations, and In-Tank Setup report(s)
Page 2 of 2
6. OVERFILL PREVENTION EQUIPMENT DETAILS
Tank ID (one OPE per column)
Are both vent and tank riser piping
secondarily contained?
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
OPE Model
What is the OPE response when activated?
(Check all that apply.)
܆܆ Shut off
Flow
܆܆Restricts
Flow
܆܆ Audible
Alarm
܆܆ Visual
Alarm
܆܆ Shut off
Flow
܆܆Restricts
Flow
܆܆ Audible
Alarm
܆܆ Visual
Alarm
܆܆ Shut off
Flow
܆܆Restricts
Flow
܆܆ Audible
Alarm
܆܆ Visual
Alarm
܆܆ Shut off
Flow
܆܆Restricts
Flow
܆܆ Audible
Alarm
܆܆ Visual
Alarm
Are flow restrictors installed on vent piping
that may interfere with the OPE operation?
܆܆ Yes*
܆܆ No
܆܆ Yes*
܆܆ No
܆܆ Yes*
܆܆ No
܆܆ Yes*
܆܆ No
At what level in the tank is the OPE set to
activate? (Inches from bottom of tank)
What is the percent capacity of the tank at
which the OPE activates?
Is the OPE in proper operating condition to
respond when the stored substance
reaches the designated regulatory level?
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
܆܆ Yes
܆܆ No
7. SUMMARY OF TESTING RESULTS
OPE Inspection Results ܆܆ Pass
܆܆ Fail
܆܆ Pass
܆܆ Fail
܆܆ Pass
܆܆ Fail
܆܆ Pass
܆܆ Fail
1 8. COMMENTS
Describe all results marked “Fail” and each proposed remedy.
* Mark here if:
܆܆ Flow restrictors interfere with overfill prevention and equipment repairs required.
87-1
71SO-410C 71SO-410C 71SO-410C
79.00”78.00” 79.00”
92.75%91.81% 92.75%
87-2 91
21
Appendix B
71SO Overfill Valve in Tank Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D)= ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W)= _____________
(U)= _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B)= _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y)= _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________ Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
3URGXFW 87-1
50.50
127.50
127.50
131.50
9816
79”
9105
9816
92.75%
21
Appendix B
71SO Overfill Valve in Tank Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D)= ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W)= _____________
(U)= _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B)= _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y)= _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________ Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
3URGXFW 87-2
54.00
130.00
130.00
134.00
9816
78
9013
9816
91.81%
21
Appendix B
71SO Overfill Valve in Tank Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D)= ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W)= _____________
(U)= _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B)= _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y)= _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________ Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
3URGXFW 91
55.00
132.00
132.00
136.00
9816
79.00
9105
9816
92.75%
21
Appendix B
71SO Overfill Valve in Tank Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D)= ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W)= _____________
(U)= _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B)= _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y)= _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________ Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
3URGXFW
7901 XERXES AVENUE SOUTH
MINNEAPOLIS, MN 55431-1288
www.xerxescorp.com
952-887-1890
CAUTION: Do not use the Calibration Chart without reviewing Xerxes® Installation Manual and Operating Guidelines, and Xerxes® applicable
Limited Warranty, copies of which are in the literature packet delivered to the site, or available at www.xerxescorp.com.
3641
3659
3676
3693
3711
3728
3745
3763
3780
3797
3815
3832
3849
3867
3884
3901
3919
3936
3954
3971
3989
4006
4023
4041
4058
4076
4093
4111
4128
4146
4163
4181
4198
4216
4234
4251
4269
4286
4304
4321
4339
4357
4374
4392
4409
4427
4445
4462
4480
4497
4515
4533
4550
4568
4586
4603
4621
4638
2666
2683
2699
2715
2732
2748
2764
2781
2797
2814
2830
2847
2863
2880
2896
2913
2929
2946
2963
2979
2996
3013
3029
3046
3063
3080
3096
3113
3130
3147
3164
3181
3197
3214
3231
3248
3265
3282
3299
3316
3333
3350
3367
3384
3401
3418
3435
3453
3470
3487
3504
3521
3538
3555
3573
3590
3607
3624
1765
1779
1794
1809
1824
1838
1853
1868
1883
1898
1913
1928
1943
1958
1974
1989
2004
2019
2034
2050
2065
2080
2096
2111
2126
2142
2157
2173
2188
2204
2220
2235
2251
2266
2282
2298
2314
2329
2345
2361
2377
2393
2409
2425
2441
2456
2472
2489
2505
2521
2537
2553
2569
2585
2601
2618
2634
2650
976
988
1001
1013
1026
1038
1051
1064
1076
1089
1102
1115
1128
1141
1154
1167
1180
1193
1206
1219
1232
1246
1259
1272
1286
1299
1313
1326
1340
1353
1367
1381
1394
1408
1422
1436
1450
1464
1478
1492
1506
1520
1534
1548
1562
1576
1591
1605
1619
1634
1648
1663
1677
1692
1706
1721
1735
1750
354
362
371
380
390
399
408
417
427
436
446
455
465
475
485
495
505
515
525
535
545
555
566
576
586
597
608
618
629
640
651
661
672
683
694
706
717
728
739
751
762
773
785
796
808
820
831
843
855
867
879
891
903
915
927
939
951
964
Dipstick Calibration Chart for 10,000 Gallon - 8' Diameter SW & DWT-I Tank
DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING GALLONS
7-3/8"
7-1/2"
7-5/8"
7-3/4"
7-7/8"
8"
8-1/8"
8-1/4"
8-3/8"
8-1/2"
8-5/8"
8-3/4"
8-7/8"
9"
9-1/8"
9-1/4"
9-3/8"
9-1/2"
9-5/8"
9-3/4"
9-7/8"
10"
10-1/8"
10-1/4"
10-3/8"
10-1/2"
10-5/8"
10-3/4"
10-7/8"
11"
11-1/8"
11-1/4"
11-3/8"
11-1/2"
11-5/8"
11-3/4"
11-7/8"
12"
12-1/8"
12-1/4"
12-3/8"
12-1/2"
12-5/8"
12-3/4"
12-7/8"
13"
13-1/8"
13-1/4"
13-3/8"
13-1/2"
13-5/8"
13-3/4"
13-7/8"
14"
14-1/8"
14-1/4"
14-3/8"
14-1/2"
0-1/8"
0-1/4"
0-3/8"
0-1/2"
0-5/8"
0-3/4"
0-7/8"
1"
1-1/8"
1-1/4"
1-3/8"
1-1/2"
1-5/8"
1-3/4"
1-7/8"
2"
2-1/8"
2-1/4"
2-3/8"
2-1/2"
2-5/8"
2-3/4"
2-7/8"
3"
3-1/8"
3-1/4"
3-3/8"
3-1/2"
3-5/8"
3-3/4"
3-7/8"
4"
4-1/8"
4-1/4"
4-3/8"
4-1/2"
4-5/8"
4-3/4"
4-7/8"
5"
5-1/8"
5-1/4"
5-3/8"
5-1/2"
5-5/8"
5-3/4"
5-7/8"
6"
6-1/8"
6-1/4"
6-3/8"
6-1/2"
6-5/8"
6-3/4"
6-7/8"
7"
7-1/8"
7-1/4"
36-3/8"
36-1/2"
36-5/8"
36-3/4"
36-7/8"
37"
37-1/8"
37-1/4"
37-3/8"
37-1/2"
37-5/8"
37-3/4"
37-7/8"
38"
38-1/8"
38-1/4"
38-3/8"
38-1/2"
38-5/8"
38-3/4"
38-7/8"
39"
39-1/8"
39-1/4"
39-3/8"
39-1/2"
39-5/8"
39-3/4"
39-7/8"
40"
40-1/8"
40-1/4"
40-3/8"
40-1/2"
40-5/8"
40-3/4"
40-7/8"
41"
41-1/8"
41-1/4"
41-3/8"
41-1/2"
41-5/8"
41-3/4"
41-7/8"
42"
42-1/8"
42-1/4"
42-3/8"
42-1/2"
42-5/8"
42-3/4"
42-7/8"
43"
43-1/8"
43-1/4"
43-3/8"
43-1/2"
21-7/8"
22"
22-1/8"
22-1/4"
22-3/8"
22-1/2"
22-5/8"
22-3/4"
22-7/8"
23"
23-1/8"
23-1/4"
23-3/8"
23-1/2"
23-5/8"
23-3/4"
23-7/8"
24"
24-1/8"
24-1/4"
24-3/8"
24-1/2"
24-5/8"
24-3/4"
24-7/8"
25"
25-1/8"
25-1/4"
25-3/8"
25-1/2"
25-5/8"
25-3/4"
25-7/8"
26"
26-1/8"
26-1/4"
26-3/8"
26-1/2"
26-5/8"
26-3/4"
26-7/8"
27"
27-1/8"
27-1/4"
27-3/8"
27-1/2"
27-5/8"
27-3/4"
27-7/8"
28"
28-1/8"
28-1/4"
28-3/8"
28-1/2"
28-5/8"
28-3/4"
28-7/8"
29"
14-5/8"
14-3/4"
14-7/8"
15"
15-1/8"
15-1/4"
15-3/8"
15-1/2"
15-5/8"
15-3/4"
15-7/8"
16"
16-1/8"
16-1/4"
16-3/8"
16-1/2"
16-5/8"
16-3/4"
16-7/8"
17"
17-1/8"
17-1/4"
17-3/8"
17-1/2"
17-5/8"
17-3/4"
17-7/8"
18"
18-1/8"
18-1/4"
18-3/8"
18-1/2"
18-5/8"
18-3/4"
18-7/8"
19"
19-1/8"
19-1/4"
19-3/8"
19-1/2"
19-5/8"
19-3/4"
19-7/8"
20"
20-1/8"
20-1/4"
20-3/8"
20-1/2"
20-5/8"
20-3/4"
20-7/8"
21"
21-1/8"
21-1/4"
21-3/8"
21-1/2"
21-5/8"
21-3/4"
29-1/8"
29-1/4"
29-3/8"
29-1/2"
29-5/8"
29-3/4"
29-7/8"
30"
30-1/8"
30-1/4"
30-3/8"
30-1/2"
30-5/8"
30-3/4"
30-7/8"
31"
31-1/8"
31-1/4"
31-3/8"
31-1/2"
31-5/8"
31-3/4"
31-7/8"
32"
32-1/8"
32-1/4"
32-3/8"
32-1/2"
32-5/8"
32-3/4"
32-7/8"
33"
33-1/8"
33-1/4"
33-3/8"
33-1/2"
33-5/8"
33-3/4"
33-7/8"
34"
34-1/8"
34-1/4"
34-3/8"
34-1/2"
34-5/8"
34-3/4"
34-7/8"
35"
35-1/8"
35-1/4"
35-3/8"
35-1/2"
35-5/8"
35-3/4"
35-7/8"
36"
36-1/8"
36-1/4"
3
5
7
9
12
15
18
21
25
28
32
36
40
45
49
54
58
63
68
73
79
84
89
95
101
107
113
119
125
131
137
144
151
157
164
171
178
185
192
199
207
214
222
229
237
245
253
261
269
277
285
293
302
310
319
327
336
345
GALLONSGALLONSGALLONSGALLONSGALLONS
4656
4674
4691
4709
4727
4744
4762
4780
4797
4815
4833
4850
4868
4886
4903
4921
4939
4956
4974
4992
5009
5027
5045
5062
5080
5098
5115
5133
5151
5168
5186
5204
5221
5239
5257
5274
5292
5309
5327
5345
5362
5380
5397
5415
5433
5450
5468
5485
5503
5521
5538
5556
5573
5591
5608
5626
5643
5661
5678
5696
5713
5731
5748
5766
5783
5801
5818
5836
5853
5871
5888
5906
5923
5940
5958
5975
5992
6010
6027
6044
6062
6079
6096
6114
6131
6148
6166
6183
6200
6217
6234
6252
6269
6286
6303
6320
6337635563726389640664236440645764746491650865256542655965766593661066276643666066776694671167286744676167786795681168286845686168786894
6911692869446961
6977
6994
7010
7027
7043
7059
7076
7092
7109
7125
7141
7157
7174
7190
7206
7222
7239
7255
7271
7287
7303
7319
7335
7351
7367
7383
7399
7415
7431
7447
7463
7478
7494
7510
7526
7541
7557
7573
7588
7604
7619
7635
7651
7666
7681
7697
7712
7728
7743
7758
7774
7789
7804
7819
7835
7850
7865
7880
7895
7910
7925
7940
7955
7970
7985
7999
8014
8029
8044
8058
8073
8088
8102
8117
8131
8146
8160
8175
8189
8203
8218
8232
8246
8261
8275
8289
8303
8317
8331
8345
8359
83738387840184148428844284558469848384968510852385378550856385778590860386168629864386568669868286948707872087338746875887718784879688098821
88338846885888708883889589078919
8931
8943
8955
8967
8978
8990
9002
9013
9025
9036
9048
9059
9071
9082
9093
9105
9116
9127
9138
9149
9160
9171
9181
9192
9203
9213
9224
9234
9245
9255
9265
9276
9286
9296
9306
9316
9326
9336
9346
9355
9365
9375
9384
9394
9403
9412
9421
9431
9440
9449
9458
9467
9475
9484
9493
9501
9510
43-5/8"
43-3/4"
43-7/8"
44"
44-1/8"
44-1/4"
44-3/8"
44-1/2"
44-5/8"
44-3/4"
44-7/8"
45"
45-1/8"
45-1/4"
45-3/8"
45-1/2"
45-5/8"
45-3/4"
45-7/8"
46"
46-1/8"
46-1/4"
46-3/8"
46-1/2"
46-5/8"
46-3/4"
46-7/8"
47"
47-1/8"
47-1/4"
47-3/8"
47-1/2"
47-5/8"
47-3/4"
47-7/8"48"48-1/8"48-1/4"48-3/8"48-1/2"48-5/8"48-3/4"48-7/8"49"49-1/8"49-1/4"49-3/8"49-1/2"49-5/8"49-3/4"49-7/8"50"50-1/8"50-1/4"50-3/8"50-1/2"50-5/8"50-3/4"50-7/8"51"51-1/8"51-1/4"51-3/8"51-1/2"51-5/8"
GALLONS
XERXES CORPORATION Dipstick Calibration Chart for 10,000 Gallon - 8' Diameter SW & DWT-I Tank
51-3/4"
51-7/8"
52"
52-1/8"
52-1/4"
52-3/8"
52-1/2"
52-5/8"
52-3/4"
52-7/8"
53"
53-1/8"
53-1/4"
53-3/8"
53-1/2"
53-5/8"
53-3/4"
53-7/8"
54"
54-1/8"
54-1/4"
54-3/8"
54-1/2"
54-5/8"
54-3/4"
54-7/8"
55"
55-1/8"
55-1/4"
55-3/8"
55-1/2"
55-5/8"
55-3/4"
55-7/8"
56"
56-1/8"
56-1/4"
56-3/8"
56-1/2"
56-5/8"
56-3/4"
56-7/8"
57"
57-1/8"
57-1/4"
57-3/8"
57-1/2"
57-5/8"
57-3/4"
57-7/8"
58"
58-1/8"
58-1/4"
58-3/8"
58-1/2"
58-5/8"
58-3/4"
58-7/8"
59"
59-1/8"
59-1/4"
59-3/8"
59-1/2"
59-5/8"
59-3/4"
59-7/8"
60"
60-1/8"
60-1/4"
60-3/8"
60-1/2"
60-5/8"
60-3/4"
60-7/8"
61"
61-1/8"
61-1/4"
61-3/8"
61-1/2"
61-5/8"
61-3/4"
61-7/8"
62"
62-1/8"
62-1/4"
62-3/8"
62-1/2"
62-5/8"
62-3/4"
62-7/8"
63"
63-1/8"63-1/4"63-3/8"63-1/2"63-5/8"63-3/4"63-7/8"64"64-1/8"64-1/4"64-3/8"64-1/2"64-5/8"64-3/4"64-7/8"65"65-1/8"65-1/4"65-3/8"65-1/2"65-5/8"65-3/4"65-7/8"66"66-1/8"66-1/4"66-3/8"66-1/2"66-5/8"66-3/4"66-7/8"67"67-1/8"67-1/4"67-3/8"67-1/2"67-5/8"67-3/4"67-7/8"
68"68-1/8"68-1/4"68-3/8"
68-1/2"
68-5/8"
68-3/4"
68-7/8"
69"
69-1/8"
69-1/4"
69-3/8"
69-1/2"
69-5/8"
69-3/4"
69-7/8"
70"
70-1/8"
70-1/4"
70-3/8"
70-1/2"
70-5/8"
70-3/4"
70-7/8"
71"
71-1/8"
71-1/4"
71-3/8"
71-1/2"
71-5/8"
71-3/4"
71-7/8"
72"
72-1/8"
72-1/4"
72-3/8"
72-1/2"
72-5/8"
72-3/4"
72-7/8"
73"
73-1/8"
73-1/4"
73-3/8"
73-1/2"
73-5/8"
73-3/4"
73-7/8"
74"
74-1/8"
74-1/4"
74-3/8"
74-1/2"
74-5/8"
74-3/4"
74-7/8"
75"
75-1/8"
75-1/4"
75-3/8"
75-1/2"
75-5/8"
75-3/4"
75-7/8"
76"
76-1/8"
76-1/4"
76-3/8"
76-1/2"
76-5/8"
76-3/4"
76-7/8"
77"
77-1/8"
77-1/4"
77-3/8"
77-1/2"
77-5/8"
77-3/4"
77-7/8"
78"
78-1/8"
78-1/4"
78-3/8"
78-1/2"
78-5/8"
78-3/4"
78-7/8"
79"
79-1/8"
79-1/4"
79-3/8"
79-1/2"
79-5/8"
79-3/4"
79-7/8"80"80-1/8"80-1/4"80-3/8"80-1/2"80-5/8"80-3/4"80-7/8"81"81-1/8"81-1/4"81-3/8"81-1/2"81-5/8"81-3/4"81-7/8"82"82-1/8"82-1/4"82-3/8"82-1/2"82-5/8"82-3/4"82-7/8"83"83-1/8"83-1/4"83-3/8"83-1/2"83-5/8"83-3/4"83-7/8"84"84-1/8"
84-1/4"84-3/8"84-1/2"84-5/8"84-3/4"84-7/8"85"85-1/8"
85-1/4"
85-3/8"
85-1/2"
85-5/8"
85-3/4"
85-7/8"
86"
86-1/8"
86-1/4"
86-3/8"
86-1/2"
86-5/8"
86-3/4"
86-7/8"
87"
87-1/8"
87-1/4"
87-3/8"
87-1/2"
87-5/8"
87-3/4"
87-7/8"
88"
88-1/8"
88-1/4"
88-3/8"
88-1/2"
88-5/8"
88-3/4"
88-7/8"
89"
89-1/8"
89-1/4"
89-3/8"
89-1/2"
89-5/8"
89-3/4"
89-7/8"
90"
90-1/8"
90-1/4"
90-3/8"
90-1/2"
90-5/8"
90-3/4"
90-7/8"
91"
91-1/8"
DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING DIPSTICKREADING
9518
9526
9535
9543
9551
9559
9567
9575
9583
9590
9598
9605
9613
9620
9627
9634
9641
9648
9655
9662
9668
9675
9681
9688
9694
9700
9706
9712
9718
9723
9729
9734
9740
9745
9750
9755
9760
9764
9769
9773
9777
9781
9785
9789
9793
9796
9799
9802
9805
9808
9810
9812
9814
9815
9816
9816
GALLONS GALLONS GALLONS GALLONS GALLONS
x810SD1.3 - 07/05fbf