HomeMy WebLinkAboutOPI 2024CERS = California Environmental Reporting System, ID = Identification, UST = Underground storage tank, ICC = International Code Council, A/V = Audible and visual
UNDERGROUND STORAGE TANK
OVERFILL PREVENTION EQUIPMENT INSPECTION REPORT FORM (Page 1 of 1)
Type of Action Installation Inspection Repair Inspection 36 Month Inspection
I. FACILITY INFORMATION
CERS ID
10022950
Date of Overfill Prevention Equipment Inspection
8/30/2024
Business Name (Same as Facility Name or DBA-Doing Business As.)
Ming ARCO AM/PM
Business Site Address
4203 Ming Ave.
City
Bakersfield
ZIP Code
93309
II. UNDERGROUND STORAGE TANK SERVICE TECHNICIAN INFORMATION
Name of UST Service Technician Performing the Inspection (Print as shown on the ICC Certification.)
Bruce W. Hinsley
Phone #
(661) 706 - 4321 Ext.
Contractor/Tank Tester License #
971259
ICC Certification #
8032698
ICC Certification Expiration Date
6/26/2025
Overfill Prevention Equipment Inspection Training and Certifications (List applicable certifications.)
1193980
III. OVERFILL PREVENTION EQUIPMENT INSPECTION INFORMATION
Inspection Method Used: Manufacturer Guidelines (Specify) OPW Overfill Prevention
Industry Code or Engineering Standard (Specify)
Engineered Method (Specify)
Attach the inspection procedures and all documentation required to determine the results. # of Attached Pages:
Tank ID: (By tank number, stored product, etc.) 87 #1 87 #2 87 #3 91
What is the tank inside diameter? (Inches) 90 90 90 90
Is the fill piping secondarily contained? Yes No Yes No Yes No Yes No
Is the vent piping secondarily contained? Yes No Yes No Yes No Yes No
Overfill Prevention Equipment Manufacturer(s) OPW OPW OPW OPW
What is the overfill prevention equipment
response when activated?
(Check all that apply.)
Shuts Off Flow Shuts Off Flow Shuts Off Flow Shuts Off Flow
Restricts Flow Restricts Flow Restricts Flow Restricts Flow
A/V Alarm A/V Alarm A/V Alarm A/V Alarm
Are flow restrictors installed on vent piping? Yes No Yes No Yes No Yes No
At what level in the tank is the overfill prevention
set to activate? (Inches from bottom of tank.) 78 78 76 79
What is the percent capacity of the tank at which
the overfill prevention equipment activates? 92 93 91 93
Is the overfill prevention in proper operating
condition to respond when the substance
reaches the appropriate level?
Yes Yes Yes Yes
No
(Specify in section V.)
No
(Specify in section V.)
No
(Specify in section V.)
No
(Specify in section V.)
IV. SUMMARY OF INSPECTION RESULTS
Overfill Prevention Inspection Results Pass Fail Pass Fail Pass Fail Pass Fail
V. COMMENTS
All items marked “Fail” must be explained in this section. Any additional comments may also be provided here.
VI. CERTIFICATION BY UST SERVICE TECHNICIAN CONDUCTING THIS INSPECTION
I hereby certify that the overfill prevention equipment was inspected in accordance with California Code of Regulations, title 23, division 3,
chapter 16, section 2637.2 and all the information contained herein is accurate.
UST Service Technician Signature
If the facility has more components than this form accommodates, additional copies of this page may be attached.
21
Appendix B
71SO Overfill Valve in Tank Initial Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D) = ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W) = _____________
(U) = _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B) = _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y) = _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________
Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
21
Appendix B
71SO Overfill Valve in Tank Initial Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D) = ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W) = _____________
(U) = _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B) = _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y) = _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________
Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
21
Appendix B
71SO Overfill Valve in Tank Initial Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D) = ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W) = _____________
(U) = _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B) = _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y) = _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________
Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
21
Appendix B
71SO Overfill Valve in Tank Initial Shut off Level Worksheet
Important: This is meant to be supplemental worksheet and not a substitute to following the installation
manual instructions. All length measurements are in inches. Please contact the Authority Having Jurisdic-
tion (AHJ) and review local, state, and national codes to determine the regulatory requirements governing
shut-off capacity in your region, as well as take into account other considerations such as extreme tank tilt.
Take the following measurements with the valve in-
stalled in the tank:
Distance from the 71SO inlet tube flange to the cast
lug in the 71SO body (see figures), upper tube length.
Note: the Upper Tube Length must be at least 16” to in-
clude the protective bend in the tube.
(D) = ______________________
Distance from the 71SO inlet tube flange to the top and
bottom of lower tube, valve length.
(W) = _____________
(U) = _____________
Distance from the 71SO inlet tube flange to the bottom
of the tank. Note: If a tank bottom protector is present it
may be necessary to add this thickness to dimension
(OPW 6111 & 61TP models add 0.6”)
(B) = _____________
From the tank calibration chart provided by tank manu-
facturer find the dipstick number (Y) which corresponds
to the 100% volume.
(Y) = _____________
1. To determine shut-off percentage:
Subtract upper tube length (D) from distance to tank
bottom (B)
(X) = (B) – (D) - 2” =________________________
Using the tank calibration chart provided by the tank
manufacturer determine the tank capacity at the cal-
culated (X) dimension and the 100% volume (Y) tank
capacity.
(X) tank capacity in gallons = _______________
(Y) tank capacity in gallons = _______________
SO% = (X) capacity / (Y) capacity x100 = __________
Note: The overfill valve must be installed per AHJ require-
ments and all applicable local, state, and national codes. If
the overfill valve is set above the allowable shut-off percent-
age the overfill valve must be removed and replaced. For
reference 40 CFR part 280 Subpart B Section 280.20 overfill
valves should be set to a maximum of 95%.
(B)
To Tank
(D)
Upper
Tube
(W) Valve
Length,
bottom of
cut
(Y)
Tank
Chart
100%
Volume
Dipstick
(U) Valve
Length,
top of cut
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
0-1/8"16 7-3/8"402 14-5/8"1041 21-7/8"1838 29-1/8"2744 36-3/8"3718
0-1/4"19 7-1/2"411 14-3/4"1053 22"1853 29-1/4"2760 36-1/2"3736
0-3/8"23 7-5/8"421 14-7/8"1066 22-1/8"1868 29-3/8"2776 36-5/8"3753
0-1/2"26 7-3/4"430 15"1078 22-1/4"1883 29-1/2"2793 36-3/4"3770
0-5/8"30 7-7/8"439 15-1/8"1091 22-3/8"1898 29-5/8"2809 36-7/8"3787
0-3/4"34 8"449 15-1/4"1104 22-1/2"1913 29-3/4"2826 37"3804
0-7/8"38 8-1/8"459 15-3/8"1117 22-5/8"1928 29-7/8"2842 37-1/8"3822
1"42 8-1/4"468 15-1/2"1130 22-3/4"1943 30"2858 37-1/4"3839
1-1/8"47 8-3/8"478 15-5/8"1143 22-7/8"1958 30-1/8"2875 37-3/8"3856
1-1/4"51 8-1/2"488 15-3/4"1155 23"1973 30-1/4"2891 37-1/2"3874
1-3/8"56 8-5/8"498 15-7/8"1168 23-1/8"1988 30-3/8"2908 37-5/8"3891
1-1/2"61 8-3/4"508 16"1181 23-1/4"2003 30-1/2"2924 37-3/4"3908
1-5/8"65 8-7/8"518 16-1/8"1195 23-3/8"2018 30-5/8"2941 37-7/8"3925
1-3/4"71 9"528 16-1/4"1208 23-1/2"2033 30-3/4"2957 38"3943
1-7/8"76 9-1/8"538 16-3/8"1221 23-5/8"2048 30-7/8"2974 38-1/8"3960
2"81 9-1/4"548 16-1/2"1234 23-3/4"2064 31"2991 38-1/4"3977
2-1/8"86 9-3/8"558 16-5/8"1247 23-7/8"2079 31-1/8"3007 38-3/8"3995
2-1/4"92 9-1/2"569 16-3/4"1261 24"2094 31-1/4"3024 38-1/2"4012
2-3/8"98 9-5/8"579 16-7/8"1274 24-1/8"2110 31-3/8"3040 38-5/8"4030
2-1/2"103 9-3/4"590 17"1287 24-1/4"2125 31-1/2"3057 38-3/4"4047
2-5/8"109 9-7/8"600 17-1/8"1301 24-3/8"2140 31-5/8"3074 38-7/8"4064
2-3/4"115 10"611 17-1/4"1314 24-1/2"2156 31-3/4"3090 39"4082
2-7/8"121 10-1/8"621 17-3/8"1328 24-5/8"2171 31-7/8"3107 39-1/8"4099
3"127 10-1/4"632 17-1/2"1341 24-3/4"2187 32"3124 39-1/4"4116
3-1/8"134 10-3/8"643 17-5/8"1355 24-7/8"2202 32-1/8"3141 39-3/8"4134
3-1/4"140 10-1/2"654 17-3/4"1368 25"2218 32-1/4"3157 39-1/2"4151
3-3/8"147 10-5/8"664 17-7/8"1382 25-1/8"2233 32-3/8"3174 39-5/8"4169
3-1/2"153 10-3/4"675 18"1396 25-1/4"2249 32-1/2"3191 39-3/4"4186
3-5/8"160 10-7/8"686 18-1/8"1409 25-3/8"2264 32-5/8"3208 39-7/8"4203
3-3/4"167 11"697 18-1/4"1423 25-1/2"2280 32-3/4"3225 40"4221
3-7/8"174 11-1/8"708 18-3/8"1437 25-5/8"2296 32-7/8"3241 40-1/8"4238
4"181 11-1/4"720 18-1/2"1451 25-3/4"2311 33"3258 40-1/4"4256
4-1/8"188 11-3/8"731 18-5/8"1465 25-7/8"2327 33-1/8"3275 40-3/8"4273
4-1/4"195 11-1/2"742 18-3/4"1479 26"2343 33-1/4"3292 40-1/2"4291
4-3/8"202 11-5/8"753 18-7/8"1493 26-1/8"2359 33-3/8"3309 40-5/8"4308
4-1/2"210 11-3/4"765 19"1507 26-1/4"2374 33-1/2"3326 40-3/4"4326
4-5/8"217 11-7/8"776 19-1/8"1521 26-3/8"2390 33-5/8"3343 40-7/8"4343
4-3/4"225 12"788 19-1/4"1535 26-1/2"2406 33-3/4"3360 41"4361
4-7/8"232 12-1/8"799 19-3/8"1549 26-5/8"2422 33-7/8"3377 41-1/8"4378
5"240 12-1/4"811 19-1/2"1563 26-3/4"2438 34"3394 41-1/4"4396
5-1/8"248 12-3/8"822 19-5/8"1577 26-7/8"2454 34-1/8"3411 41-3/8"4413
5-1/4"256 12-1/2"834 19-3/4"1591 27"2470 34-1/4"3428 41-1/2"4430
5-3/8"264 12-5/8"846 19-7/8"1606 27-1/8"2486 34-3/8"3445 41-5/8"4448
5-1/2"272 12-3/4"858 20"1620 27-1/4"2501 34-1/2"3462 41-3/4"4465
5-5/8"280 12-7/8"870 20-1/8"1634 27-3/8"2517 34-5/8"3479 41-7/8"4483
5-3/4"288 13"881 20-1/4"1648 27-1/2"2533 34-3/4"3496 42"4500
5-7/8"296 13-1/8"893 20-3/8"1663 27-5/8"2550 34-7/8"3513 42-1/8"4518
6"305 13-1/4"905 20-1/2"1677 27-3/4"2566 35"3530 42-1/4"4535
6-1/8"313 13-3/8"917 20-5/8"1692 27-7/8"2582 35-1/8"3547 42-3/8"4553
6-1/4"322 13-1/2"930 20-3/4"1706 28"2598 35-1/4"3564 42-1/2"4571
6-3/8"330 13-5/8"942 20-7/8"1721 28-1/8"2614 35-3/8"3581 42-5/8"4588
6-1/2"339 13-3/4"954 21"1735 28-1/4"2630 35-1/2"3598 42-3/4"4606
6-5/8"348 13-7/8"966 21-1/8"1750 28-3/8"2646 35-5/8"3615 42-7/8"4623
6-3/4"357 14"978 21-1/4"1765 28-1/2"2662 35-3/4"3632 43"4641
6-7/8"366 14-1/8"991 21-3/8"1779 28-5/8"2679 35-7/8"3650 43-1/8"4658
7"375 14-1/4"1003 21-1/2"1794 28-3/4"2695 36"3667 43-1/4"4676
7-1/8"384 14-3/8"1016 21-5/8"1809 28-7/8"2711 36-1/8"3684 43-3/8"4693
7-1/4"393 14-1/2"1028 21-3/4"1823 29"2727 36-1/4"3701 43-1/2"4711
Calibration Chart
10,000 Gallon - 8' Diameter Double-Wall (DW-II)
www.xerxes.com For Tanks Manufactured Prior to September 1, 2008
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
DIPSTICK
READING GALLONS
43-5/8"4728 51-3/4"5863 59-7/8"6957 68"7964 76-1/8"8827 84-1/4"9467
43-3/4"4746 51-7/8"5880 60"6973 68-1/8"7978 76-1/4"8839 84-3/8"9475
43-7/8"4763 52"5897 60-1/8"6990 68-1/4"7993 76-3/8"8850 84-1/2"9482
44"4781 52-1/8"5914 60-1/4"7006 68-3/8"8007 76-1/2"8862 84-5/8"9489
44-1/8"4798 52-1/4"5932 60-3/8"7022 68-1/2"8022 76-5/8"8874 84-3/4"9497
44-1/4"4816 52-3/8"5949 60-1/2"7038 68-5/8"8036 76-3/4"8885 84-7/8"9504
44-3/8"4833 52-1/2"5966 60-5/8"7054 68-3/4"8050 76-7/8"8897 85"9511
44-1/2"4851 52-5/8"5983 60-3/4"7071 68-7/8"8065 77"8908 85-1/8"9518
44-5/8"4869 52-3/4"6000 60-7/8"7087 69"8079 77-1/8"8920 85-1/4"9524
44-3/4"4886 52-7/8"6018 61"7103 69-1/8"8093 77-1/4"8931 85-3/8"9531
44-7/8"4904 53"6035 61-1/8"7119 69-1/4"8107 77-3/8"8942 85-1/2"9538
45"4921 53-1/8"6052 61-1/4"7135 69-3/8"8122 77-1/2"8954 85-5/8"9544
45-1/8"4939 53-1/4"6069 61-3/8"7151 69-1/2"8136 77-5/8"8965 85-3/4"9551
45-1/4"4956 53-3/8"6086 61-1/2"7167 69-5/8 8150 77-3/4"8976 85-7/8"9557
45-3/8"4974 53-1/2"6103 61-5/8"7183 69-3/4"8164 77-7/8"8987 86"9563
45-1/2"4991 53-5/8"6120 61-3/4"7199 69-7/8"8178 78"8998 86-1/8"9569
45-5/8"5009 53-3/4"6138 61-7/8"7215 70"8192 78-1/8"9009 86-1/4"9575
45-3/4"5026 53-7/8"6155 62"7231 70-1/8"8206 78-1/4"9020 86-3/8"9581
45-7/8"5044 54"6172 62-1/8"7247 70-1/4"8220 78-3/8"9031 86-1/2"9587
46"5061 54-1/8"6189 62-1/4"7263 70-3/8"8234 78-1/2"9042 86-5/8"9593
46-1/8"5079 54-1/4"6206 62-3/8"7278 70-1/2"8247 78-5/8"9052 86-3/4"9598
46-1/4"5096 54-3/8"6223 62-1/2"7294 70-5/8"8261 78-3/4"9063 86-7/8"9603
46-3/8"5114 54-1/2"6240 62-5/8"7310 70-3/4"8275 78-7/8"9074 87"9609
46-1/2"5131 54-5/8"6257 62-3/4"7326 70-7/8"8289 79"9084 87-1/8"9614
46-5/8"5149 54-3/4"6274 62-7/8"7342 71"8302 79-1/8"9095 87-1/4"9619
46-3/4"5166 54-7/8"6291 63"7357 71-1/8"8316 79-1/4"9105 87-3/8"9624
46-7/8"5184 55"6308 63-1/8"7373 71-1/4"8330 79-3/8"9116 87-1/2"9629
47"5201 55-1/8"6325 63-1/4"7389 71-3/8"8343 79-1/2"9126 87-5/8"9633
47-1/8"5219 55-1/4"6342 63-3/8"7404 71-1/2"8357 79-5/8"9136 87-3/4"9638
47-1/4"5236 55-3/8"6359 63-1/2"7420 71-5/8"8370 79-3/4"9146 87-7/8"9642
47-3/8"5254 55-1/2"6375 63-5/8"7436 71-3/4"8384 79-7/8"9157 88"9646
47-1/2"5271 55-5/8"6392 63-3/4"7451 71-7/8"8397 80"9167 88-1/8"9650
47-5/8"5289 55-3/4"6409 63-7/8"7467 72"8411 80-1/8"9177 88-1/4"9654
47-3/4"5306 55-7/8"6426 64"7482 72-1/8"8424 80-1/4"9187 88-3/8"9658
47-7/8"5324 56"6443 64-1/8"7498 72-1/4"8437 80-3/8"9197 88-1/2"9662
48"5341 56-1/8"6460 64-1/4"7513 72-3/8"8450 80-1/2"9206 88-5/8"9665
48-1/8"5359 56-1/4"6477 64-3/8"7529 72-1/2"8464 80-5/8"9216 88-3/4"9668
48-1/4"5376 56-3/8"6493 64-1/2"7544 72-5/8"8477 80-3/4"9226 88-7/8"9671
48-3/8"5394 56-1/2"6510 64-5/8"7559 72-3/4"8490 80-7/8"9235 89"9674
48-1/2"5411 56-5/8"6527 64-3/4"7575 72-7/8"8503 81"9245 89-1/8"9676
48-5/8"5429 56-3/4"6544 64-7/8"7590 73"8516 81-1/8"9254 89-1/4"9679
48-3/4"5446 56-7/8"6561 65"7605 73-1/8"8529 81-1/4"9264 89-3/8"9681
48-7/8"5464 57"6577 65-1/8"7621 73-1/4"8542 81-3/8"9273 89-1/2"9682
49"5481 57-1/8"6594 65-1/4"7636 73-3/8"8555 81-1/2"9282 89-5/8"9684
49-1/8"5498 57-1/4"6611 65-3/8"7651 73-1/2"8568 81-5/8"9292 89-3/4"9684
49-1/4"5516 57-3/8"6627 65-1/2"7666 73-5/8"8580 81-3/4"9301
49-3/8"5533 57-1/2"6644 65-5/8"7682 73-3/4"8593 81-7/8"9310
49-1/2"5551 57-5/8"6661 65-3/4"7697 73-7/8"8606 82"9319
49-5/8"5568 57-3/4"6677 65-7/8"7712 74"8619 82-1/8"9328
49-3/4"5585 57-7/8"6694 66"7727 74-1/8"8631 82-1/4"9337
49-7/8"5603 58"6710 66-1/8"7742 74-1/4"8644 82-3/8"9345
50"5620 58-1/8"6727 66-1/4"7757 74-3/8"8656 82-1/2"9354
50-1/8"5638 58-1/4"6744 66-3/8"7772 74-1/2"8669 82-5/8"9363
50-1/4"5655 58-3/8"6760 66-1/2"7787 74-5/8"8681 82-3/4"9371
50-3/8"5672 58-1/2"6777 66-5/8"7802 74-3/4"8694 82-7/8"9380
50-1/2"5690 58-5/8"6793 66-3/4"7817 74-7/8"8706 83"9388
50-5/8"5707 58-3/4"6810 66-7/8"7831 75"8718 83-1/8"9396
50-3/4"5724 58-7/8"6826 67"7846 75-1/8"8731 83-1/4"9405
50-7/8"5742 59"6842 67-1/8"7861 75-1/4"8743 83-3/8"9413
51"5759 59-1/8"6859 67-1/4"7876 75-3/8"8755 83-1/2"9421
51-1/8"5776 59-1/4"6875 67-3/8"7891 75-1/2"8767 83-5/8"9429
51-1/4"5794 59-3/8"6892 67-1/2"7905 75-5/8"8779 83-3/4"9437
51-3/8"5811 59-1/2"6908 67-5/8"7920 75-3/4"8791 83-7/8"9444
51-1/2"5828 59-5/8"6924 67-3/4"7934 75-7/8"8803 84"9452
51-5/8"5845 59-3/4"6941 67-7/8"7949 76"8815 84-1/8"9460
XERXES 10,000 Gallon - 8' Diameter Double-Wall (DW-II)
Reprinted - Feb16