HomeMy WebLinkAbout2009 SB989 RESULTS IIIIIII VIII III IIII 65
IE
SWRCB,January 2002 Page 1 of 5
Secondary Containment Testing Report Form
This form is intended for use by contractors performing periodic testing of UST secondary containments systems. Use the appropriate
pages of this form to report results for all components tested. The completed form, written test procedures, and printout from tests(if
applicable),should be provided to the facility owner/operator for submittal to the local regulatory agency.
1. FACILITY INFORMATION
Facility: AT&T Corporation Service Date: 01/16/2009
Facility Address: 1520 20th St.,Bakersfield CA 93301 GEO PAR#CAKO10
Facility Contact: Grant Armstrong Facility Phone:
Date Local Agency Was Notified of Testing: 01/14/2009 Test Type: Initial
Name of Local Agency Inspector if present during testing): Ernie Madena
2. TESTING CONTRACTOR INFORMATION
Company Name:Tait Environmental Services
Technician Providing Test: Scott Johnson
Credentials ®CSLB Licensed Contractor ❑SWRCB Licensed Tank Tester
®ICC UST Service Technician
License Type:A B ASB C-10 HAZ License Number: 588098
Manufacturer Training
Manufacturer Component(s) Date Training Expires
ICC 5252040-UT 11/10/2009
INCON 337353761 01/17/2009
3. SUMMARY OF TEST RESULTS
Component Pass Fail Not Repairs Component Pass Fail Not Repairs
Tested Made Tested Made
Annular#CAK010U001 ® ❑ ❑ ❑ ❑ ❑
Fill Sump#CAK010U001 ® ❑ ❑ ❑ ❑ ❑
Spill Bucket#CAKOIOU001 ® ❑ ❑ ❑ ❑ ❑
Piping Sump#CAKOl0U001 ® ❑ ❑ ❑ ❑ ❑
Vent Secondary#CAKOIOU001 ® ❑ ❑ ❑ ❑ ❑
Supply Secondary#CAK01 OU001 ® ❑ ❑ ❑ ❑ ❑
Return Secondary#CAK01 OU001 ® ❑ ❑ ❑ ❑ ❑
Transition Box/Sump#CAKOI OU001 ® ❑ ❑ ❑ ❑ ❑
❑ ❑ ❑ F1 ❑ ❑ ❑
❑ ❑ ❑ El ❑ ❑ ❑
❑ ❑ ❑ ❑ ❑ I❑
11:1 1 El 1011
If hydrostatic testing was performed,describe what was done with the water after completion of tests:
Water was pumped into 2-55 gallon drums and left on site.
CERTIFICATION OF TECHNICIAN RESPONSIBLE FOR CONDUCTING THIS TESTING
To the best of my knowledge,the fact stated in this c ent are accurate and in full compliance with legal requirements
Technician's Signature .w Date 01/16/2009
IIIIIII VIII III IIII 66
IE
SWRCB,January 2002 Page 2 of 5
4.TANK ANNULAR TESTING
Test Method Developed by ❑ Tank Manufacturer ® Industry Standard ❑ Professional Engineer
❑ Other(Specify)
Test Method Used ❑ Pressure ® Vacuum ❑ Hydrostatic
❑ Other(Specify)
Test Equipment Used:4"Dial Guage Equipment Resolution: .2
Tank#CAKO1OU001 Tank# Tank# Tank#
Is Tank Exempt From Testing?(1) ❑ Yes ® No ❑ Yes ❑ No ❑ Yes ❑ No ❑ Yes ❑ No
Tank Capacity: 8,000 Gallon
Tank Material: Steel Clad
Tank Manufacturer: Joor
Product Stored: Diesel
Wait Time between applying 1 Hr
pressure/vacuum/water and starting
test:
Test Start Time: 1:15pm
Initial Reading(Ri): -10 Hg
Test End Time. 2:15pm
Final Reading(Rf): -10 Hg
Test Duration: 1 Hr
Change in Reading(Rf-Ri): 0
Pass/Fail Threshold or Criteria: 0
Test Result . ® Pass ❑ Fail ❑ Pass ❑ Fail ❑ Pass ❑ Fail ❑ Pass ❑ Fail
Was Sensor Removed for Testing? ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
Was Sensor properly replaced and ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
verified functional after testing?
Comments include any information on repairs made prior to testing,and recommended follow-up for failed tests
Sensor was placed at lowest point in tank annular space and tested during the Monitor Certification
(1)Secondary containment systems where the continuous monitoring automatically monitors both the primary and secondary containment,such as
sysrtems that are hydrostatically monitored or under constant vacuum,are exempt from periodic containment testing. {California Code of
Regulations,Title 23,Section 2637(a)(6))
SWRCB,January 2002 Page 3 of 5
5. SECONDARY PIPE TESTING
Test Method Developed by ❑ Piping Manufacturer ® Industry Standard ❑ Professional Engineer
❑ Other(Specify)
Test Method Used ® Pressure ❑ Vacuum ❑ Hydrostatic
❑ Other(Specify)
Test Equipment Used:4"Dial Guage Equipment Resolution: .)
Piping Run#Vent Piping Run#Sply Piping Run#Rtrn Piping Run#
#CAK01OU001 #CAK01OU001 #CAK01OU001
Piping Material: Fiberglass Poly Poly
Piping Manufacturer: Ameron Western Fiberglass Western Fiberglass
Piping Diameter: 2" 1" 1.5"
Length of Piping Run: 35' 120' 120'
Product Stored: Diesel Diesel Diesel
Method and location of piping-run Test Boot Test Boot Test Boot
isolation:
Wait Time between applying 1 Hr 1 Hr 1 Hr
pressure/vacuum/water and starting
test:
Test Start Time: 1:15pm 1:15pm 1:15pm
Initial Reading(Ri): 5 PSI 5 PSI 5 PSI
Test End Time: 2:15pm 2:15pm 2:15pm
Final Reading(Rf): 5 PSI 5 PSI 5 PSI
Test Duration: 1 Hr 1 Hr 1 Hr
Change in Reading(Rf-Ri): 0 0 0
Pass/Fail Threshold or Criteria: 0 0 0
Test Result ® Pass ❑ Fail 1110 Pass ❑ Fail ® Pass ❑ Fail ❑ Pass ❑ Fail
Comments include any information on repairs made prior to testing,and recommended follow-up for failed tests
The Vent line is 2"Ameron LCX.
SWRCB,January 2002 Page 4 of 5
6.PIPING SUMP TESTING
Test Method Developed by ❑ Sump Manufacturer ® Industry Standard ❑ Professional Engineer
❑ Other(Specify)
Test Method Used ❑ Pressure ❑ Vacuum ® Hydrostatic
❑ Other(Specify)
Test Equipment Used: INCON Equipment Resolution: .0006
Sump#Piping Sump#Trans Sump# Sump#
#CAKO10U001 #CAKO10U001
Sump Diameter 42" 24"x 30"
Sump Depth 39" 34"
Sump Material Fiberglass Fiberglass
Height from Tank Top to Top of 15" 17
Highest Piping Penetration
Height from Tank Top to Lowest 17" 34"
Electrical Penetration
Condition of sump prior to testing Good/Clean Good/Clean
Portion of Sump Tested(1) 2"Above Piping 2"Above Piping
Does turbine shut down when
sump sensor detects liquid(both ❑ Yes ❑ No ® NA ❑ Yes ❑ No ® NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
product and water)?*
Turbine shutdown response time NA NA
Is sytem programmed for fail-safe ❑ Yes ❑ No ® NA ❑ Yes ❑ No ® NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
shutdown?*
Was fail-safe verified to be ❑ Yes ❑ No ® NA ❑ Yes ❑ No ® NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
operational?*
Wait time between applying
pressure/vacuum/water and starting 15 Min. 15 Min.
test
Test Start Time 1:29 pm 1:46 pm 1:29 pm 1:46 pm
Initial Reading Ri) 2.8910 2.8910 7.2874 7.2873
Test End Time 1:45 pm 2:01 pm 1:45 pm 2:01 pm
Final Reading R 2.8909 2.8908 7.2873 7.2872
Test Duration 15 Min. 15 Min. 15 Min. 15 Min.
Change in Reading Rf-Ri .0001 .0002 .0001 .0001
Pass/Fail Threshold or Criteria .002 .002
Test Result ® Pass ❑ Fail ® Pass ❑ Fail ❑ Pass ❑ Fail ❑ Pass ❑ Fail
Was sensor removed for testing? ® Yes ❑ No ❑ NA ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
Was sensor properly replaced and ® Yes ❑ No ❑ NA ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
verified functional after testing?
Comments include any information on repairs made prior to testing,and recommended follow-up for failed tests
Sensor was placed at lowest point in the Sump and tested during the Monitor Certification.
(1)If the entire depth of the sump is not tested,specify how much was tested. If the answer to any of the questions indicated with an
asterisk(*)is"NO"or"NA",the entire sump must be tested.(See SWRCB LG-160)
SWRCB,January 2002 Page 5 of 5
8.FILL RISER CONTAINMENT SUMP TESTING
Facility is Not Equipped With Fill Riser Containment Sumps ❑
Fill Riser Containment Sumps are Present,but were Not Tested ❑
Test Method Developed by ❑ Sump Manufacturer ® Industry Standard ❑ Professional Engineer
❑ Other(Specify)
Test Method Used ❑ Pressure ❑ Vacuum ® Hydrostatic
❑ Other(Specify)
Test Equipment Used: INCON Equipment Resolution: .0006
Fill Sump#Fill Fill Sump# Fill Sump# Fill Sump#
#CAK010U001
Sump Diameter: 42"
Sump Depth: 41"
Height from Tank Top to Top of None
Highest Piping Penetration:
Height from Tank Top to Lowest 25"
Electrical Penetration:
Condition of sump prior to testing: Good/Clean
Portion of Sump Tested: 2"Above Collar
Sump Material: Fiberglass
Wait time between applying 15 Min.
pressure/vacuum/water and starting
test:
Test Start Time: 2:2 m 2:44 m
Initial Reading Ri): 3.6327 3.6335
Test End Time: 2:44 pm 2:59 m
Final Reading 3.6337 3.6339
Test Duration: 15 Min. 15 Min.
Change in Reading Rf-Ri : .001 .0004
Pass/Fail Threshold or Criteria: .002
Test Result: ® Pass ❑ Fail ❑ Pass ❑ Fail ❑ Pass ❑ Fail ❑ Pass ❑ Fail
Is there a sensor in the sump? ® Yes ❑ No ❑ Yes ❑ No ❑ Yes ❑ No ❑ Yes ❑ No
Does the sensor alarm when either ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
product or water is detected?
Was sensor removed for testing? ® Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA ❑ Yes ❑ No ❑ NA
Was sensor properly replaced and ® yes ❑ No ❑ NA ❑ Yes 01 No ❑ NA ❑ Yes ❑ No El NA ❑ Yes ❑ No ❑ NA
verified functional after testing? -�l
Comments include any information on repairs made prior to testing,and recommended follow-up for failed tests
Sensor was placed at lowest point and tested during the Monitor Certification.
� HT�
F^E L' J cn
ft:45 PM ~'44 PM
F SU�p LEAK ���' REF�RT `~ ' L^'~ 'E" "='`~'
TLL
rRHNSlT
F.I. f'APTED PM
TEST STARTED f Pf" STfflTED- Z'2'
EST STARTED 01,"16/2009 01/16/2009—
T
8EGIw LEVE� 7.2874 IN -- -�
.
END TInE lf�45 PM ' � Z. ' ' ' ''
END D�rE 01/16/2009 — -- ---'
EN0 L��� 7 2873 7K � — -�
./ _ , �� LEAK THRESHOLD 0,002 IN
` LEAK THP ES+QLn 0,002 I TEST RESULT PASSED
|. TEST �ESL!i-r PASSED
` F-Bx.
�
ST�RTED -`' ~''^`'^"
� �r �n
TES� S.�RT�D — ' -- ---`
8EGIN LEVEL 2 END T� -�
� ��44 PM
END TIME �l.�"49 Pt, EHD DATE 01/16/2009
END DATE 6/2009 END LEVEL 4.6682 Ik
^ END LEVEL 2.8989 IN LEAK THRESHOLD 8.002 IN
<�
LEAK THRESHOLD 0.002 IN TEST RESULT PASSED
� TEST RESULT PASSED
[ ~`
/
�
;�TT
ITT 152�
� 152@ 20S7. ' i 8HKERFI��
` 3HKERFIELA � '� CA. - '
C� '
[ ' `
P�
59
'
]� SUMp LEAK T�STREPO��
SUMP �EHK TES� REp0RT i�
FILL
i TIvHNSlT
� �� ���� � �
TEST STARTED A-?-46 P�'l ST�RT[] 0
7--ST CTHRTED 01/16/2809 B[GTN L�)EL � '- -~~^
^'���� IN
BEGI* LEVEL 7 2873 I� �� TIME
^ � 'Z.159 PM
_ND TIME ��'0z PM | �[ND DATE 0�/1�/2009
END DATE 01/16/2009 �uD LEV[L 3.6339 {N
�ND LEV[L 7.2872 IN ' LFHK T�R[SHOLD 0.882
LE�K THRESHOLD 0.082 lH TES� RESULT '
TEST RESULT PASSED � ~`'�~\
� rESr STAHTB)
�'_-.T 7riRTED *Ca6 Pm �� STH�� ���
TESr "Ap7EC. BEGlNi-EVEL 4.6681'1N
8EGl!� -�VEL 2.8910 IH
END TIM':' �:5g pr!
END rwE 01 pn ' EN0 DATE 03./16/2009 ~
�HD i)HrE 01/16/2009 END LEVE-i .6679 I�
[ND LEVEL 2,O908 IN � LEHK THRE3HOLD 0.0�02 IN
L�HK THRESHOLD 0.002 IN . TEST RESUL- PASSED
' TES` R[SULT PASSED
TEST DATE: : K]EOPAR: CAK010 PAGE | OF \
Monitoring System Certification
For Use By All Jurisdictions Within the State of California
Authority Cited: Chapter 6.7, Health and Safety Code;Chapter 16, Division 3, Title 23, California Code of Regulations
This form must be used to document testing and servicing of monitoring equipment.A separate certification or report must be prepared for each
monitoring system control panel by the technician who performs the work.A copy of this form must be provided o the tanK system owner .opera or.The
owner/operator mus su mi a copy of this form to the local agency regulating UST systems within 30 days of test date.
A. General Information
Facility: AT&T Corporation GEO PAR#CAK010
Address: 1520 20th St. City: Bakersfield Zi : 93301
Facility Contact Person: Grant Armstrong Contact Phone No: 661 327-6903
Make/Model of Monitoring System: Veeder Root-TLS 350 Service Date: 01/16/2009
B. Inventory of Equipment Tested/Certified
Check the appropriate boxes to Indicate specific equipment Inspectediserviced:
Tank ID: #CAK0100001 Tank ID:#CAK010A002
®In-Tank Gauging Probe Model:846390-105 ®In-Tank Gauging Probe Model:846390-105
®Annular Space or Vault Sensor Model:794390-420 ®Annular Space or Vault Sensor Model:794390-420
®Piping Sump/Trench Sensor(s) Model:794380-208 ®Piping Sump if Trench Sensor(s) Model:794380-208
®Fill Sump Sensor(s) Model:794380-208 ❑Fill Sump Sensor(s) Model:
❑Mechanical Line Leak Detector Model: ❑Mechanical Line Leak Detector Model:
❑Electronic Line Leak Detector Model: ❑Electronic Line Leak Detector Model:
®Tank Overfill/High Level Sensor Model:790091-001 ®Tank Overfill/High Level Sensor Model:790091-001
❑Other(Specify equipment type and model in Section E on Page 2) ❑Other(Specify equipment type and model in Section E on Page 2)
Tank ID: Tank ID:
❑In-Tank Gauging Probe Model: ❑In-Tank Gauging Probe Model:
❑Annular Space or Vault Sensor Model: ❑Annular Space or Vault Sensor Model:
❑Piping Sump/Trench Sensor(s) Model: ❑Piping Sump/Trench Sensor(s) Model:
❑Fill Sump Sensor(s) Model: ❑Fill Sump Sensor(s) Model:
❑Mechanical Line Leak Detector Model: ❑Mechanical Line Leak Detector Model:
❑Electronic Line Leak Detector Model: ❑Electronic Line Leak Detector Model:
❑Tank Overfill/High Level Sensor Model: ❑Tank Overfill/High Level Sensor Model:
❑Other(Specify equipment type and model in Section E on Page 2) ❑Other(Specify equipment type and model in Section E on Page 2)
Dispenser ID: Dispenser ID:
❑Dispenser Containment Sensor(s) Model: ❑Dispenser Containment Sensor(s) Model:
❑Shear Valve(s) ❑Shear Valve(s)
❑Dispenser Containment Float(s)and Chain(s) ❑Dispenser Containment Float(s)and Chain(s)
Dispenser ID: Dispenser ID:
❑Dispenser Containment Sensor(s) Model: ❑Dispenser Containment Sensor(s) Model:
❑Shear Valve(s) ❑Shear Valve(s)
❑Dispenser Containment Float(s)and Chain(s) ❑Dispenser Containment Float(s)and Chain(s)
Dispenser ID: Dispenser ID:
❑Dispenser Containment Sensor(s) Model: ❑Dispenser Containment Sensor(s) Model:
❑Shear Valve(s) ❑Shear Valve(s)
❑Dispenser Containment Float(s)and Chain(s) ❑Dispenser Containment Float(s)and Chain(s)
If the facility contains more tanks or dispensers,copy this form.Include Information for every tank and dispenser at the facility.
C. Certification-I certify that the equipment Identified In this document was inspected/serviced in accordance with the
manufacturers'guidelines.Attached to this Certification Is Information(e.g.manufacturers'checklists)necessary to verify
that this information is correct and a Plot Plan showing the layout of monitoring equipment. For any equipment capable of
generating such reports,I have also attached a copy of the report; (check all that apply):
® ystem set- ®Alarm history report
Technician Name (Print): JOHNSON SCOTT Si nature.
Certification No: 835636 License No: 588098
Testing Company Name: TAIT ENVIRONMENTAL Phone No: (714)560-8222
SERVICES
Page 1 of 4
Monitoring System Certification
Address: 1520 20th St. Bakersfield 93301 Service Date: 01/16/2009
D. Results of Testing/Servicing
Software Version Installed: 120.00
Complete the fol owing checklist:
•Yes ❑ No* Is the audible alarm operational?
•Yes ❑ No* Is the visual alarm operational?
•Yes ❑ No* Were all the sensors visually inspected, functionally tested, and cofirmed operational?
•Yes ❑ No* Were all sensors installed at lowest point of secondary containment and positioned so that other
equipment will not interfere with their proper operation?
❑Yes ® No* If alarms are relayed to a remote monitoring station, is all communications equipment(e.g. modem)
operational?
❑ N/A
❑Yes ❑ No* For pressurized piping systems, does the turbine automatically shut down if the piping secondary
containment monitoring system detects a leak, fails to operate, or is electrically disconnected?
If yes:which sensors
initiate positive shut- ❑ Sump/Trench Sensors ❑ Dispenser Containment Sensors
® N/A down?:
Did you confirm positive shut-down due to leaks and sensor failure/disconnection? ❑Yes ®No
®Yes ❑ No* For tank systems that utilize the monitoring system as the primary tank overfill warning device (i.e. no
mechanical overfill prevention valve is installed), is the overfill warning alarm visible and audible at the
❑ N/A tank fill point(s)and operating properly?If so, at what percent of tank capacity does the alarm trigger?:
90%
❑Yes* ® No Was any monitoring equipment replaced? If yes, identify specific sensors, probes, or other equipment
replaced and list the manufacturer name and model for all replacement parts in Section E below.
Was liquid found inside any secondary containment systems designed as dry systems?
❑
Yes* ® No If yes, check the type(s)of liquid found and describe causes in Section E, below. ❑Product ❑Water
®Yes ❑ No* Was monitoring system set-up reviewed to ensure proper settings?Attach set up reports, if applicable
❑Yes ® No* Is all monitoring equipment operational per manufacturers specifications?
*In Section E below, describe how and when these deficiencies were or will be corrected.
E. Comments
The modem is not connected at this time.
Page 2 of 4
Monitoring System Certification
Address: 1520 20th St. Bakersfield 93301 Service Date: 01/16/2009
F. In-Tank Gauging/SIR Equipment ®Check this box if tank gauging is used only for inventory control
❑Check this box if no tank gauging or SIR Equipment is installed
This section must be completed if in-tank gauging equipment is used to perform leak detection monitoring
Complete the fol owing checklist
•Yes ❑ No* Has all input wiring been inspected for proper entry and termination, including testing for ground
faults?
•Yes ❑ No* Were all tank gauging probes visually inspected for damage and residue buildup?
®Yes ❑ No* Was accuracy of system product level readings tested?
•Yes ❑ No* Was accuracy of system water level readings tested?
•Yes ❑ No* Were all probes reinstalled properly?
•Yes ❑ No* Were all items on the equipment manufacturers maintenance checklist completed?
* In the Section H below, describe how and when these deficiencies were or will be corrected
G. Line Leak Detectors (LLD): ®Check this box if LLDs are not installed
Complete the fol owing checklist
❑Yes ❑ No* For equipment start-up or annual equipment certification, was a leak simulated to verify LLD
performance?
❑ N/A Simulated Leak Rate(check all that apply) ❑ 3.0 g.p.h ❑0.1 g.p.h 1:10.2 g.p.h
❑Yes ❑ No* Were all LLDs confirmed operational and accurate within regulatory requirements?
❑Yes ❑ No* Was the testing apparatus properly calibrated?
❑Yes ❑ No* For mechanical LLDs, does the LLD restrict product flow if it detects a leak?
❑ N/A
❑Yes ❑ No* For electronic LLDs, does the turbine automatically shut off if the LLD detects a leak?
❑ N/A
❑Yes ❑ No* For electronic LLDs, does the turbine automatically shut off if any portion of the monitoring system is
disabled or disconnected?
❑N/A
❑Yes ❑ No* For electronic LLDs, does the turbine automatically shut off if any portion of the monitoring system
malfunctions or fails a test?
❑ N/A
❑Yes ❑ No* For electronic LLDs, have all accessible wiring connections been visually inspected?
❑ N/A
❑Yes ❑ No* Were all items on the equipment manufacturers maintenance checklist completed?
* In the Section H below, describe how and when these deficiencies were or will be corrected
H. Comments
The monitoring system is operational at this time therefore no ground faults are present.
Suction system
Page 3 of 4
Monitoring System Certification
Address: 1520 20th St. Bakersfield 93301 Service Date: 01/16/2009
UST monitoring Site Plan
. . . . Fti . . . . . . . . . . . . . .,
r + i(4.? SV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iYS . . . . . . . . . . . . . . . . . . . . �,
. . . . . . . . . . . . . .
a �
. . . . . . it . . .
. . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date map was drawn: 01/16/2009
Instructions
.If you already have a diagram that shows all required information, you may include it, rather than this page,
with your Monitoring System Certification. On your site plan, show the general layout of tanks and piping.
Clearly identify locations of the following equipment, if installed: monitoring system control panels; sensors
.monitoring tank annular spaces, sumps, dispenser pans, spill containers, or other secondary containment
areas; mechanical or electronic line leak detectors; and in-tank liquid level probes (if used for leak detection).
In the space provided, note the date this Site Plan was inspected.
Page 4 of 4
SWRCB,January 2006
SPILL BUCKET TESTING REPORT FORM
This form is intended for use by contractors performing annual testing of UST spill containment structures. The completed form and printout from
tests(if applicable),should be provided to the facility owner/operator for submittal to the local regulatory agency.
1.FACILITY INFORMATION
Facility Name:AT&T Corporation I Date of Testing:01/16/2009
Facility Address: 1520 20th St. Bakersfield CA 93301 IGEOPAR#CAKOIO
Facility Contact: Grant Armstrong Facility Phone:
Date Local Agency Was Notified of Testing: 01/14/2009
Name of Local Agency Inspector if present during testing): Ernie Madena
2.TESTING CONTRACTOR INFORMATION
Company Name: TAIT ENVIRONMENTAL SERVICES
Technician Conducting Test:JOHNSON SCOTT
Credentials: ®CSLB Contractor ®ICC Service Tech ❑SWRCB Tank ❑Other(Specify)
Tester
License Number (s):A ASB HAZB C-10. 588098
3.SPILL BUCKET TESTING INFORMATION
Test Method Used ®Hydrostatic ❑Vacuum ❑Other
Test Equipment Used: INCON I Equipment Resolution: .0006
Identify Spill Bucket(By Tank Number, 1#CAKO1OU001 2 3 4
Stored Product,etc)
Bucket Installation Type ❑Direct Bury ❑Direct Bury ❑Direct Bury El Direct Bury
®Contained in Sump ❑Contained in Sump ❑Contained in Sump ❑Contained in Sump
Bucket Diameter inches 12"
Bucket Depth inches 14"
Wait Time between applying 15 Min.
vacuum/water and start of test
Test Start Time: 2:2 m / 2:44 pm
Initial Reading Ri): 4.6687 / 3.6335
Test End Time: 2:44 pm / 2:5 9prn
Final Reading 4,6682 / 3.6339
Test Duration: 15 Min. / 15 Min.
Change in Reading -Ri : .0005 / .0004
Pass/Fail Threshold or Criteria: 0
Test Result Pass
Comments: Test water left onsite
CERTIFICATION OF TECHNICIAN SPONSIBLE FOR CONDUCTING THIS TESTING
I hereby certify that all the information contained in this ort is true,accurate and in full compliance with legal requirements
Technician's Signature 'v Date 01/16/2009
F3 �llj I
--j'I.,
B4'RRISCI U-1),
'0 20'f I i FuEL ALAR(l
b jAI-q 16 '2,f 0 9 1 29 PM 1 8 U--A--18 4 L-,
-a bi 4 1 N I E', C i C rj 1 :3-1 F-f-,l
,I
3 FEll R'E 0 R,T
REf'-")R'r
"AllEfIfill ALARM
AI'L, FIJI-Irlie)IIS
SU!'"IF
I t JAN I b, �-009 1
C
27 0 6 L 2.
c 'Dor� ' -
j0%
TL-7 vOLUME 5294 '.�ALIS
HEICIiT P5 I .5 4 1 1,JC,HE'-j D I.E"EL Tf,14Cm�
6JATER V01. o cl I I'lloo I
w�)'TEP 0,00 1 N 0,11 F-S- I NVENTORY INCREASE
TEVIP 60.8 DEG F I NCREAS-E START
I N-TANK 'ib�ARH J�IN 16, "'009 1 '32' f--P-1
134 GALS OVERFILL ic�LAPH VOLUME 296 GAL2
ULLAGP, 66 (>)LS JAN 16 2009 1 33 PI'l HE I GHT = 5 1 .lj 4 INCHES
9-Ox HUAGE= 41 GALS -(JATER = 0,00 1 INCHE'S
'p,' VOLUME 164 GALS TEMP = 62 0 DEG F
17 1 NCHES
i-iE I(�H'r
WATER �)(A,
WATER 0.00 11,1'�H E.S I END
TEHP 51?,o DEG F i I E, '2 o o ri 1 34 pl-I
VOLUME = 7093 GiL�LS
01D X HEIGHT = I NCH I--*S'
WATER 0.00 1 NCHU�
TEHP 61 .8 DEG F
I Il(,RF.ASE= 1 17 97
NFT I NCRFASE= 1795
3EI-Ook' ALHIRM
L 5:A[INULAR
FUM- ALARM
JAN 16, 2CIC19 1 2 8 FPl
fit'fl'IlCi-�13 I CiVC110
1520 20TH
66 069 1
JAN 16. '2009 1 1-11
2'EN202 �)L�)Ril
' %
I :FILL "LIMP 15,20 2'i-D'I'li 2;T
l'US R-f 'I
^!F*I vi 'm 9:330 1
'3'ff,
FUEL 6c,1 --869-10-46
,I A 11 t 2 A 0 9 1 2'H ["I ALA,
��T i�Tlj-. RfP-,)RT
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE OF
F.'It- R FiUiRTI l
bi��%,-' NV JF-TURE fK3N
L TA ' Rl
16. '2009 1 :41 PI'l
JAI-] 16. 200• 1 37 P11 15`0 2'0111 'T
93301
r.C.I --01 6':i 1 ED 4 C.
J i�i 11 1 6 '20 0 9 1 45 PH
RE'PORT
152,10 is'r
PLARI-1
--OP ri BHKERSFJEf-f'l-l>; 9,3'.'301 T 2:'�`UDDEN L0.;-`S- hl-HPM
L 4:biW�' T611Y ;�illlJUUiR 661 046
FLIEL hl.riRM JAN 16, 2'01119 1 43 PH REPORT
JAN I t 0 09 1 Ja P111
T I
'clYSTEM REPORT VOLUIE = 5'277 G(-�US
ULLAGE = ''("25 G)LS
T i L i f)D E N L 0'�5 A L f i RJ�1 9U%' ULU(E- 1924 13;iLcj
TO VOLLIHE = 5273 GALS
T PRODUCT AL.fO,l HE I GHT = 51 .38 1 NCHES'
WATER VOL 0 GALS
wf�TER = 0.lJ0 I N 1--'Y i El
1�i-fkllf fILARI-1 TEMP = G-1 .6 DEG F
T '--*l:Dll.'-,-,FJ. TKOO)YOLOACIC12
LOW PRODUCT H"'Li:01
JAN 16, 200-i f:410 M f 2-',:D I ES,E L TYUCAKi')10000
VOLUME 155 GALS
ULLAGE = 95 GALS
ULI.,,�iGE= 7 fj GHLS
Ti:; VOLUME = 154 GALS
HE I GHT = 10.711 I HCHES
Bl' W)T ER VOL = 14 GALS
1520 WATER = 0.K-1 I NCHES
BhKE92-F I ELF)-G 9 L-1-30 I TEHP . 60.Ej DEG F
661-869- 6 184
IN-JANK AUiRl"I
T :MDUL TKllC,'AYCJl(lH002 JAN 16, 2009 1 :44 PH BID X
SUDDEN LOSS ALARM
JAN 16. 2009 1 :40 PH
-;,Tlf--,Il.l STATUS REPORT
T 2:',-.'-UDfjEN L(JE12; ALARM
T t�Y A002'
"1:1''11ESFI. TVIAC' OICI 15"Cl 20TH SST
F'I.Jf-.L LEVEI..
JAN 161 21009 1 '40 PH 661-069-1046
jr`ll+j 16. '20119 1 :46 pfll
1 521) 20TH ST
661 -06'9--1I-W6 STATUS REPORT
JAN It- 2CIC19 1 45 PH L02S AlJiPll
IN-TW' fiLHRH
T '-":01ESEL
PROBE '_'MT ',�YSTEH STHTU, REP4-JRT
IAN 1b" 2009 1 :40 P1.1
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE OF
I I-AKcll 0 WAKER'S-F I U,J) _J I f
FUEL, LEVEL
20TH ',71' b t1l I--0 6 184 f, TAf1 16, 51 Ftl
r,KE'R':"FI Ell,-f_'f� 93:: Cl I
JHll lu., 2009 1 49 PH
ItS> 2009 1 :46 PM sTAT Ll.' REPORT
T :SUDDEN ALARM I 1AVEIATOY."j' REPORT
T I 'DIR.Fift. TVit(;mj%'CjIOU00l
V "HLS
OIA-IME 52 77 G
LILl.A(;E ',-"7 25 GALS D.H I. F I Ell 9 '3 1_1 I
K" 011WaE= 1924 GALS h61 c;69- 1 .4 C.
TC VOLUME = 5269 GAL.S
HEIGHT - 51 .38 1[l C'I i E"7j
WATER VOL = 0 GHLS
WATER = 0.00 INCHES
11,1-JANY ALARM TEMP = &3'. I DEG F
SY. TKJ'l • IR RFF'OR'
r 2.;F j I E'S F.I T}-,';V_4AK 0 1 CIA Cl 1-12". F;I_L FUNCIID.-)NS N0Rt,,iA_'
JoN 16, 21-IC,9 1 48 PH VOLUt"IE = 173 GALs
UUACM 77 GALS
9M, UU..`GE= SQ GALS
TC VOLUME = 17 6 A I.,S_
HEIGHT = 20.89 INCHE2
WATER VOL = 0 GALS
WATER
U.CIO I N('HE-
TEMP = 63.5 DEG F
x};01 Cl END T I f)I EBEL. YK ft(t K 0 100001
ST PRC)O-E OUT
2,009 55 PH
661-069. 1 04G,
-RiN 16. 21009 1 :48 PM
S T H
-l'US REPORT
ALI,
1 N j,;iNY (�L;41'1 11 cw�K'Ol cl
T 1TW -4,010HOO2 IFJ-,-2o *20TH ST
1,V)*.xl. PPODUl-l' HLARN B�4:EPSFIELD,Cf� 93301
T"V-1 lr,- 2009 1 :49 PM 661 1 10146
JW-1 1 201119 1 :58 PM
93301 AU. FUNc-71 ONS. NORP,wil"
661 069-1 84b
JW 16. '2009 1 :413 pilli T 2:DIE'SEL lllilC'€1,1,'OICIA002
PR'ODE 01il,
16., 21-lc9 I 51 F-m
9Ef-`-)R'f
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE OF
JAN 16., -1009 39 PM
10 U.S. f-OR T 2;ET"I'l NGS
I 2CITH ti;T' 2`11STEM LANGUAGE FX
ENGLISH BOARD I J,10f)
13ALER'SF I F.J.1 C:f-i 9�,J:30 I
G.61 1369--1846 -Y1c'.TEt-1 LATE/TIME FORMAT DAUD RATE' I 2C
HC)N DD HH:M1,1:SS x1-1 PAR I T" ODD
STOr
ljfi[q 161 121009 3:23 P1111 3 I,IT I STOP
Bf.'fT)k-.!A01 CAY010 DATA LENGTH: 7 DATA
1520 20TH ST F.".:p-2022 SECURITY
EA1:.'EJz.'SF I ELD,CA 93301 1"ODE : )0(X*A x
SYSTE'll STATUS REP%'_)RT 661-069-1846 D I Al. T'''PE TONE
ANSWER ON I RI NG
ALI, FUNC77101'IS NORMAL SHIFT TIME 1 ':30 f4l 1`10DEM SETUP _--TR I NG
SHIFT TIME *-, DISABLED
INVENTOR`! REPORT SHIFT TIME 3 DISABLED DIAL T(_:NE INTERVAL: .j2
SHIFT TIME 4 D I SABLED
T I :D I El'-;EL TY;1CAK01QU001 TANK PER TST' NEEDED WRN RECEIVER SETUP:
VOLUME - 5462 GALS DISABLED
ULLAGE = 2540 GALS TANK ANN TST NEEDED WRN NONE
90% ULLAGF= 1739 GALS D I SiciBLED
TO VOLUME - 5464 GALS
HEIGHT = 52.93 INCHES LINE RE-EN'BLE METHOD
WATER VOL - I I GALS PASS LINE TEST
WATER = 0.74 1 NCHES
TEMP = 59.0 DEG F I LINE PER TST 14EECIED WRN
DISABLED
LINE ANN TST NEEDED With
T '2:f j I ES*E L TK#CAK0 I OA002 DISABLED
VOLUME 184 GALS
ULLACE = 66 GALS PRINT' TC VOLUMES
90s,. ULLi:iGE= 41 GALS ENABLED HuTO DIAL TIME SETUP:
TC VOLUME = 184 GALS TEMP COMPENSATION N()NE
HEIGHT = 22-1. 17 1 NCHES VALUE (DEG F , : 60.0
WATER VOL = 0 GALS STICK HEIGHT OFFSET
WATER = 0.00 INCHES D 12,A'b L E D
TEMP. = 58.3 DEG F
11--PROTOCOL DATA FORMAT
END # * X 1( HEIGHT
DA''"LIGHT SAVINC, TIME
ENABLED
START DATE
MAR WEEK 3 SU14
START T I ME
2:00 AM
END DATE
NOV WEEK 2 SUN
ENE) 'rIME END OF ME22'.ACIF
2:00 t*1 D I 21ABLED
RE-DIRECT LOCAL PR1NT-.',_"UT AUTO DIAL ALARM 2JETUP
DISABLED
FJJR%'-+ PPOTOOOL PREFLx.'
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAKO 10 PAGE OF
SETUP
THF-Rt"ImL ((`EFF 000450
THWK DImME'I'ER 30.00 L I :FILI.
PR()FILE 4 PT2 T?I --�r3l'HTE I-JCLE F,L.
FULL V; L. 2 5 G hTE(4ORY 's.TP S-upip
-''T C-obf- 5 1 NCH �!C)L. 18�
THE'Pfli-iL 1-10EFF : .00CW50 I o I 1,10-11 "'.,61- 125'
T(itll` DIAMETER 82.00 7.5 1 NCH VOL G 2 L 11.4 uMp
Ti�;NK% PROFILE I vr ;
FULL VOL 6002 (S,I NGLE FLOHT)
PIPING '3UPIP
F D",A T S I -- 4.0 1 IIJ,
FL()AT SIZ'F-- 4.0 IN. UATE]"', 1 NG 2.-
HIC,'H WATER LIMIT' kUPTURE
WfiTER tJARNING 2.0 3.0 01-21P-46LE FLOAT)
HIC;H WATER LIMIT: :3.0 I1A'X OR LABEL, VOL: -151-1
LIMIT 100%,
HA:--`4 C'R LABEL W)1- 8002 250
-,FI I I
-L LIMIT 90,10 1-111-�,H PRODUCT 10010
7201 250 L. 4;DA4 1'f7NK ANNULAR
HIGH PRODUCT 95% TR I-`TATF t S I NGI.E FLOA,i
DELIVERY I.Altfl-T 0% CATEG"OF"V : ANNULAR SPACE-
0
DEL. LIMIT 4 9%
39 1 Low PRODUCT
LEAK AL(�Pll LIMIT: 10099 L b:ANNUDAR
LOW PRODW.-f 4000 SUDDEN LOSE; LftlIT:
99 TRI—STATE' (SINGLE FLOAT)
LEAK ALARM LIMIT' 99 Tr)N f,.* T I LT 0.00 CATEWRY : ANNULAR 1.4-,AcE
SUDDEN LOSS: LIMIT: 99
TWlY TILT 0.40 MANIFOLDED TANKS,
Tu: NONE
TANKS L 6:f'IFIING BOX
T14: NONE DELI VERY DELAY 99 11111114 (SINGLE FI-Orvi,,%
CATEGORY : PIPINC,' SUMP
LEW,' N I N PER I OD I C: 0%
C)
I- N fiNNIJAL, ON
PER 101)1( TEST TYPE
QUICK
m1,4•iwAL. TECS'1' F(-QL LEAK. TEST I-IFTHOF)
ALARM DISABLED EXTERNAL I NI"UT SETUP
TEST ON DH 1'E
PE160Filf- TEST FAIL JAI'l 16, -jcjCj9
ALARM DISABLEL) START TIME : DISABLED I I :GEN RUN
TEST RATE :0.20 GAL,'HR GENERATOR
Gk%-62 FAIL DURATI ON 2 HOURS. OPEN
2 1
AD RM D I SA B,L,E D TST EARLY STOP:D 15ABLEJ) Tfi*.'#.. HLL TANK
ANN TEST AVERAGING'. OFF
PER TEST AVERHGING: OFF TEST DAILY TA NY, 2
TANK TEST' NOTIFY' OFF START TI Mf--' : 12:CIO ANj
TEST RATE :0.20 GAL...-Hp
TsT SIPHON BREAK:OFF DURATI ON : 2 HOURS
TST EARLY ':TOF--D I S iBL.El)
DELIVER"I BELAY
TES'}' REPORT FORPYmiT
E7NHANCEE)
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE -5 OF
0 0'1'f-UT flli"" NET UP
R I :OVER' FILL, ALARM IN-TANK ALARM
TYPE: T
STANDARD RE(:011C.11-fATION SETUP 'K01 1 o Ll 0 o I
N;)F'HmLL'-/ OPEN
JAN 16- 3009 12:30 P1,1
I N-TANE. ALABIS AUTOIIATI ' DAILY CLuSIN,a
ALL: LL ALARM TIME: 2:00 AM H I Gli WATER ALARI-1
Al.l.:HICH PRODUCT ml-ARrl JAN I 6. 2109 It :27 Arl
PRODUCT ALARM PERIOI)IC: APR I -mjcl�' 10:'30 rim
R 21:f-lAIN TANK LOW MODE: MONTHLY OVERC I LL ALARP-1
JAI C-,TYPE: TEHP C:0-IFE14SATION 2009 1 :33 yj
STANDARD STANDARD JAN 16. ;'009 009 11 :32 AM
OPEN (-iF'P 11 , 2006 10:25 Atl
'-.;L()T FUEL METER TANY
- -' - -iP LOW PRODUCT ALARM
I II-TANK ALARMS TANK MAP Ef, TY APR I I , 2-008 10-:-211 AM
I I -LOL-J PRODUCT ALARM 30, "007 '11 :53 AM
NOV 12. 2007 10:03 AM
R Tic�NY LFAK ALARM S
TYPE -1-IDDEN LOSS ALARM
STANDARD JAN 16, 2009 11 :28 AH
NORMALLY OPEN PROBE our
JAN 16-- 2009 1 :55
LI ELI ID SEN2OR ALHS JAN 16, 2009 11 :28 AM
L 1 :FUEL ALARM JAN IS. 2009 3:37 ptvj
L 2:FUEI. ALARM
L 5:FUEL. ALARM H ISTOR",' REPORT HIGH WATER WARNING
L 2:SENSOR OUT ALARM JAN 16, 2009 11 :37 AM
L 3:SENSOR OUT Hl-mktl if SYSTEM ALARM APR 11 , 2008 10:30 AM
L 5:SENSOR OUT AL;01 PAPER OUT
L I :SHORT ALARM JAN 16, 2009 1---551 Pm
L. 2:SHORT ALARM PRINTER ERROR DELIVERY NEEDED
L 5:SHORT ALARM JAN l6. 2009 12:51 F-11 APR 11 , 2008 10.'20 AM
BATTER"i' 12 OFF NOV 30. 2007 11 :53 AM
P 4:STP SHUT DOWN JAN 1 . 1996 8:00 Hj°j NOV 12, 2007 10:0:3 AM
TYPE: SYS SECURITY WARN IN1.3
STANDARD JAN 18- 2008 0:57 AM
NORMALLY OPEN 0SL-D INOR RATE WARN
DEC' 11-1. 2008 9:38 Arj
SEP 18, 2008 10:06 Aq-j
LfQUID SENS--'-)R ALMS S E P 18-- 2008 6:58 AM
AI.L:FUEL ALARM
ALL:2ENSOR OUT ALARM
ALL:SHORT ALARM
IN 5".
TYPE:
2TaNDORD ri. 'X END ;k
NORMALLY OPEN
NO ALARM ASS I GNMENTS, E ND
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE OF
Mi RT
T
OVERHLL iibARm
I - 2 0 Cl ALARI'l HIS"FORY
L
bL&I PRODUCT O;LARM I :FILL C-lul"IR R, E f:�,;i��N
JAN 0-9 1 ',40 FIM STP c'UMP
APR' I I '2HJ 0 8 1 :40 PH FUEL ALARI°j FUEL t;LA1211
JAN
JAN 16� 2009 1 :C'Dn FT,l 1 :,37 F-111.1
)EN L,0,2,�?i i b�ol 12E,1120R
JAI'4 16. 2009 1 :40 FTI FUE-1 Al-mRI'l
HIGH PR,.'JfIJC'f' ALARH JAN 15. 2009 4:04 Pill
APR 11 , 0 0 H_ 1 :51 F-1111 c-ENc"9 "UT FiLHRH
EN OUT ALARI'l
APR [ 1 0 0.2:* 1 :31@ PM JAN 15. 2009 3:54 PM 5 '--'009 4: 14 PH
i-WRI 11 Cl Cl 8 1 1 :3') i4l
I NVAL 11:) FUEL LEVEL
JAN 16 2009 1 :51 FIM
1 009 1 :40 P1.11
11 2008 1 :41-1 Pm
PR(.', t",UT
Ji�)N 16, '200L-i 1 :51 Pil •
JAN 16. 2009 1 :40 ftl END ,t
Jif4 20
4 15, 09 2.37 PH
PlAX. PRODUCT ALARM
,JriN 16, 2009 1 :49 PH
JAN 16.. 2009 1 48 Pi
JAN 16, 2009 1 :41 PM
HISTOR"i REP R 'oR r
ITT
SEN20P r";LARM
AN)'4U]
-IR ALARm
ANNUL.f:�P' SPACE
SUMP FUEL ALARM
END FUEL (:if.,ARM JAN 16.. "'2009 1 :36 ptj
JhN 16, 2004 2 :29 Fti
FUEL ftiLHRM 20I)SOR OUT ALARM
JN01 IS, 2009 4: 12 PH
JAN 15. 4:0;-j* i;'m
SEI'4c"OP OUT Ob4RH FUEL, oLARM
JAN 15. 2009 3:37 1}r°1 JAN 15. 2009 4; 1 1 pp�j
t�LFiRH I-11,81TORY RU.,ORT
T :3
END 3'i k END
END
TEST DATE: 1/16/2009 CLIENT: AT&T, GEOPAR: CAK010 PAGE 7 OF
*
ALAN 11121-iRY -L.'&-]
"LARI'l
L 5,A4NULAR
ANNULAR SPHOE
FUEL Al,i*M
JHN 16- 2009 1 :28 PH
FUEL. ALARM
,JW,J 15, 2009 4,32, P 1,1
SENSOR IJT mL,Hkl,,l
JAN 15. 2009 :3 37 H"I ENE)
HLARII REPORT
ENSOR ALARM
L e:
OTHER '-iEMSORS
�ARI`l H PEPORT
G7LAPH
L 6:pjF-ING BO.A. E ND
FULL. ALARM
JA4 I E2009: I "c pl"I
FUEL m.hRrl
JAN 15. 2009 4 PH
I< ALARV-1
JAN !S- d«9 4:0o PH
END REVICBION LB.'FL
%l'EM7jl(')N 120.00
S.,
OFTW�RF# 346120-100—A
CREATED —
830160-002-6
Y-21'Ell FEmTURES:
\£R! !C !N—TANJ"" Tf--�Sf'S
ANNUAL fN—'ro4,JI',' TESTS
(SLE)
TEST DATE: 1/162009 CLIENT: AT&T, GEOPAR: CAK010 PAGE OF
TA 1 T
RISING TO TNI CNAlLtNO! 2131 S. Dupont Drive, Anaheim,CA 92806 ,
11 p::71 4156018222 www.tait.com
February 9, 2009
VIA FED EX: 8664 6539 1810
Bakersfield Fire Department
1501 Truxtun Ave.
Bakersfield CA 93301
Re: Secondary Containment Testing
Monitoring System Certification
Spill Bucket Testing
AT&T Corporation
1520 20th STREET, BAKERSFIELD, CA
GEOPAR: CAK010
To Whom it May Concern:
Enclosed are the results for the following tests completed on January 16th, 2009:
■ Secondary Containment Testing Report Form
■ Monitor System Certification Report Form
■ Spill Bucket Testing Report Form
Please do not hesitate to call me if you have any questions.
Very Truly Yours,
M tt hew L. Denison
Program Manager
MD
TACLIENTSIAT&T1ATT Document ManagemenhAMCAK0101Cover Letters120090209_CAK010_ATTSB98909-
II
ATTMC09_SB989,MC&SB_Bakersfield.doc
i
i
w
CA HO 588098 1 AZ Iic#095984 1 NV licll 0049666 1 TX IIc#CR0000041